Guestbook
Hello everyone,
you may put your web-site comments here, but the guestbook is not a help hotline.
In order to provide a possibility of answering questions I have set up a Technical Forum on the website. This will allow people to ask a question and others to answer.
I will not answer technical questions in the guestbook and do not encourage others to do so.
Post a Comment
- Oops, you forgot something.
117 Comments
Reply
Jon Laughton
01:57 PM on July 04, 2010
Fascinating website. Thanks for all the work in creating it - keep up the good work!
(Sadly, I don't have an NC Deckel, but I do have a manual FP1, and I have some experience of the latest DMG machining centres, which are impressive machines.)
Regards,
Jon Laughton
(Sadly, I don't have an NC Deckel, but I do have a manual FP1, and I have some experience of the latest DMG machining centres, which are impressive machines.)
Regards,
Jon Laughton
Reply
MaikH
07:23 PM on June 06, 2010
Hi Kattenes,
my defective bought FP2NC ( with the siemens 3m control) is fixed now. It took me about 50 hours - with a lot of wrong guesses. The culprit was the 3m contol output card, which feeds the contol voltages to the motor driver cards. A memory chip in this card was faulty (FlipFlop) which ha d to decouple the DAC from the databus. So the machines servos started rumoring when a certain feed speed, and axis was selected. ...
Best Regards - Maik
my defective bought FP2NC ( with the siemens 3m control) is fixed now. It took me about 50 hours - with a lot of wrong guesses. The culprit was the 3m contol output card, which feeds the contol voltages to the motor driver cards. A memory chip in this card was faulty (FlipFlop) which ha d to decouple the DAC from the databus. So the machines servos started rumoring when a certain feed speed, and axis was selected. ...
Best Regards - Maik
Does anyone have a NSV80 power board available that he is willing to sell?
It is no problem when the board is not working, as long as the printed circuit board itself is in decent shape.
Thanks in advance.
It is no problem when the board is not working, as long as the printed circuit board itself is in decent shape.
Thanks in advance.
Reply
Mark Byrne
06:54 PM on May 21, 2010
Good to see I am from australia and the technical backup for our fp42 NC is hard to get
Reply
Sami Ullah
11:41 AM on May 05, 2010
Dear Kattenes,
I have tried to email you at kattens@web.de, but it shows error exhusted storage and e-mail is not being sent to you. As i have posted a comment on tecnical fourm and pictures are not getting attached with it.
Best Regards,
Sami Ullah
I have tried to email you at kattens@web.de, but it shows error exhusted storage and e-mail is not being sent to you. As i have posted a comment on tecnical fourm and pictures are not getting attached with it.
Best Regards,
Sami Ullah
Reply
Sami Ullah
11:29 AM on May 05, 2010
Dear Kattenes,
Greetings,
Thanks for your kind reply.
I have read the web site very carefully and did so as it is mentioned
there, but problem still exist. I am sending you the pictures what i have
did.
Pictures file is attached with this e-mail.
Best Regards,
Sami Ullah
1. Switch ON machine
2. 4 way jumper removed.
3. Turn off machine
4. Put jumper back
5. Turn ON machine
6. Blank Screen with error nr ?30?
7. Turn mode switch to 16
Which shows error nr ?03?
8. ?Clear? button is pressed
9. ?Enter? button is pressed
10. At end ?Not Ok? is displayed, with error nr?30?
Greetings,
Thanks for your kind reply.
I have read the web site very carefully and did so as it is mentioned
there, but problem still exist. I am sending you the pictures what i have
did.
Pictures file is attached with this e-mail.
Best Regards,
Sami Ullah
1. Switch ON machine
2. 4 way jumper removed.
3. Turn off machine
4. Put jumper back
5. Turn ON machine
6. Blank Screen with error nr ?30?
7. Turn mode switch to 16
Which shows error nr ?03?
8. ?Clear? button is pressed
9. ?Enter? button is pressed
10. At end ?Not Ok? is displayed, with error nr?30?
Reply
MAeko
12:26 PM on April 21, 2010
DOES ANYBODY HAVE A documentation for deckel nc Fp3a 2102?My mashine has broken and I dont have a documentation.I would be very grateful if you would be sent to my email adress. licanin.jovke@gmail.com
Reply
MAeko
12:26 PM on April 21, 2010
DOES ANYBODY HAVE A documentation for deckel nc Fp3a 2102?My mashine has broken and I dont have a documentation.I would be very grateful if you would be sent to my email adress. licanin.jovke@@gmail.com
Hi Kattenes
The machine was quite cheap -below 2kEuros- and came directly from a NC workshop, who hasn't used it the last 2 years. Fixing defective electronics is one of my hobbys. complicated = intresting ;)
There are 3 mechanical handwheels on the machine, and I've got a lot schematics and user manuals with it. The schematic for the missing electronic handwheel was included as well, I can sent you a scan - if you want. It seems to be easy to be "reverse engineered" / copied - there are just 6 Buttons with lamps and an rotational encoder in it - no further electronics needed.
I hope that I will get it to its future place this weekend - so that I can try to fix the control (blank screen, nobuttons response / lightning..)
best regards
The machine was quite cheap -below 2kEuros- and came directly from a NC workshop, who hasn't used it the last 2 years. Fixing defective electronics is one of my hobbys. complicated = intresting ;)
There are 3 mechanical handwheels on the machine, and I've got a lot schematics and user manuals with it. The schematic for the missing electronic handwheel was included as well, I can sent you a scan - if you want. It seems to be easy to be "reverse engineered" / copied - there are just 6 Buttons with lamps and an rotational encoder in it - no further electronics needed.
I hope that I will get it to its future place this weekend - so that I can try to fix the control (blank screen, nobuttons response / lightning..)
best regards
kattenes says...
Buying such machine with a defective Siemens 3M control is a gutsy move. I would not have touched it except for parts. I hope it is not the very old machine that has been on german website for sale for a long time (very old style control console). The Siemens machines do not have handwheels. I'd much more advise you towards a Dialog control.
